New Onkyo CP-1500F Turntable tone arm gears

$18.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store
() %,

Location: Joliet, Illinois, United States
Ships to: US,
Item: 224720715515

eBay Welcome to The Speaker Port Up for sale is a brand new replacement tone arm drive gears to repair the rubberized version in an Onkyo CP-1500F turntable (or similar model that uses the same gear.) This is NOT an original unit, but a reproduction using cutting edge 3D Printing technology. It is made from PLA material which is substantially stronger than the original rubber material that breaks down/cracks/melts as a result of age, the elements, etc. Substantial time and effort and numerous versions of this gear have been produced to ensure we have as accurately as possible reproduced the original part. With this said, please read these important notes on using this part to replace your gear on the CP-1500F: Tolerances Due to limitations in the capabilities of current 3D printing technology, tolerances are not 100% exact to the original. I have personally (and successfully) tested this gear on otherwise working system that has not been modified or been damaged in any way. If your system has been modified or has damage, it is possible you may have fitment issues. Please address these modifications/damages first. Fitment Every attempt was made to try and get this gear to be a direct replacement for the original. Depending on your actual system, there may two things you may run into. I will do my best to describe each and provide instructions on how to deal with them. The gear is held onto it’s shaft by a simple, yet small C-clip. First and foremost, take care in removing this clip to prevent damage to it. Properly and completely clean the shaft to remove any grease/debris from the original gear. In addition, make certain the the motor worm gear and bottom tone arm gears are also properly and completely cleaned of any old lubrication grease/debris. I recommended using either proper turntable oil or lithium grease to re-lubricate the shaft before you put on the new gear. You do not need tons….just enough to sufficiently coat it. The center bore of the gear was drilled out using a 1/8″ bit which is about 0.125mm bigger that the 3mm shaft diameter. In the event where you shaft, for whatever reason, is larger than 3mm, then you will have to drill out the bore appropriately. Long story short, the new gear should spin freely on the shaft without the C-Clip installed. When you install back the C-Clip, the gear should continue to spin freely. If you notice that the gear becomes tight, then remove the gear from the shaft and gently sand down either the top or bottom of the gear using 80-120 grit sand paper or a file (preferred). You do NOT want to take of a lot….just enough to get that C-Clip to not bind up on the gear. Again, you should not have to do this, but just in case, wanted to pass the information along. The servo motor that drives this gear has a worm drive on it. It spins the wider end of the gear which in turn spins the tone arm gear at the bottom with the thinner end. depending on your setup, you may notice that the worm gear may not be making good contact to the new gear. There are two small screws that hold down the bracket that the servo motor is mounted to. You can simply loosen them and re-adjust the servo so it makes good contact and then tighten back up the screws. In fact, i recommend you do this no matter what just to make sure everything is good before you put it all back together again. Note: don’t make it too tight, it should have a little play between the gear and worm drive. The servo motor does not have a lot of torque so if it is too tight, it wont spin. Will this part fit other turntables? I can only verify that it fits the 1500F. You can use this part at your own risk in other systems. Note: The actual color of the gear may vary due to filament availability. Limited 30 Day Parts/Labor Warranty The Speaker Port will provide a limited 30-day warranty for this item against component failure. This is a repair/replace warranty only; it does not allow for the return of the item(s) for a refund for any reason. In addition, as this is a plastic part and can very easily be damaged due to improper use, we do not warranty against broken or worn teeth on either side of the gear. If for whatever reason you have having problems trying to get this part to work in a 1500F, please contact me….do not force the gear into use. For full details on our Warranty terms please visit our website in the Services section. General Terms and Conditions Unless otherwise specified above, the following terms and conditions apply. If you have a question about one of our items that is not answered above or below, please reach out to us. Your bid means that you have read, understood and agree to all the items listed below. Any used/repaired/restored item we sell is tested and verified to be in working condition before we list it. Any NEW items we sell that are sealed in OEM packaging are assumed to be in perfect working condition as it left the manufacturer. The condition and function of the item(s) in this listing will be accurately represented in each listing based on its known state when it leaves our hands. Unless otherwise explicitly stated in the listing above, there is no warranty or any kind provided or implied. Unless otherwise specified, we do not ship to any international destinations. Any international bids made will be cancelled accordingly. To minimize cost to our Customers, we do not ship items with insurance beyond what the carrier provides by default. We do not cheat our Customers by charging inflated shipping like many other sellers. We configure out listing shipping costs with the actual weight and dimensions and any additional handling costs (if they apply) for boxes, bubble wrap, pop-corn packing, etc. We reserve the right to cancel any bids from users with zero (or negative feedback rating) at our discretion. The only forms of payment we accept are those specified in the list. Once an item has been paid for, we typically ship within one business day. (Exceptions apply, such as holidays, weather, or other acts of God outside of our control.) In some cases, the size of an item may require more complex packing which could delay shipping. You will be promptly notified in situations such as this All items normally ship via USPS or FedEx. All sales are final. Unless otherwise specified, there are no returns accepted for any reason. If you have a question about the listing, we welcome you to send us a message about it, but please do so before bidding and/or winning an item. We have a 100% positive feedback rating. We have this because we do business in an honorable and respectable manner. We are committed to Customer satisfaction. If you have ANY issue with something we have sold, please contact us directly first in order to resolve the matter.

Frequently Asked Questions About New Onkyo CP-1500F Turntable tone arm gears in My Website

jphs.snru.ac.th is the best online shopping platform where you can buy New Onkyo CP-1500F Turntable tone arm gears from renowned brand(s). jphs.snru.ac.th delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling New Onkyo CP-1500F Turntable tone arm gears on jphs.snru.ac.th?